Nano Scale RP/I Methamphetamineby Curbshot[ Back to the Chemistry Archive ] The ratios are based on your using red phosphorus from matchbooks and iodine from tincture. DO NOT ADJUST RATIO. The reason is never once while nano pondering had a failure or half reacted product, and never yielded under 60%. So follow instructions and don't make any adjustments. From start to finish takes swim 2 hours. Give yourself 2.5 hours. You will end up with at least 0.7gm of get your dick hard meth. Don't get me wrong, swim has seen his share of failures during his adventures of cooking, but for some fucked up reason those were only seen in much larger scale cooks. Swim has taught friends this nano scale procedure because some people have a really hard time understanding the mathematics of producing meth. Learning this way will teach you the basics hands on. Ask any of the big boys: methead, warlock, placebo, rhodium; fuck, there's a lot of them now. Producing HIGH QUALITY meth fail safe and consistently is a skill that takes 100% visual/observational skills and actually knowing what is happening WHILE it is happening and knowing that fine line of needed adjustments if things don't go as planned. That makes this synth a good tool to exercise your observational skills and get you clued in on what is going on. And most importantly, a fat bowl when finished. ExtractionNB! This extraction procedure is out of date for most pseudoephedrine pills, and is likely to fail. Please refer to other documents at this site for updated instructions on how to extract pseudoephedrine. After you've done that, resume reading from the "Reaction" section below. /Rhodium Materials
Crush your pills and put in 12oz glass jar. Add the denatured alcohol and fit with lid. Shake jar hard a few minutes. Place jar into freezer for 10 minutes. Shake again and return to freezer for an additional 20 minutes. Your pseudoephedrine will be dissolved in the alcohol while the waxes and fillers will settle to the bottom. Carefully pour the top layer into a funnel with coffee filter and onto a glass dish. Evaporate the alcohol (gentle heat and/or hair dryer.) You should have around 1.5gm pseudoephedrine. ReactionMaterials
Using 2 soup cans, one on top of the other, makes a perfect source of heat to the moist sand. Construction is very simple: the lower can has holes drilled throughout it for air supply for flame. Now with candle lit in 1st can place 2nd can with sand right on top. The sand will warm instantly and your ready to go. You will be using
Place your test tube in freezer 5 minutes before adding chemicals. In the following order add: I, E, RP. Have your tape and balloon ready to go. With a dropper add 4 drops of peroxide and place balloon over test tube approx. 1cm. Tape balloon in place. Using your finger to prevent anything from entering the balloon, shake the 3 reactants to mix well. The reaction will start, now place tube into sand 2.5-3 inches and set timer for one hour. Exercise your observational skills; take notes on what you see. After a handful of runs at this soon you won't need to set a timer because you will have schooled yourself and have your own tools (sign's) that completion of the rxn is there. But for now go with 1 hour, no more no less. Blow your candle out and let tube cool in sand for 15 min. Take your now room temp. test tube and cut balloon off. Add 20ml dh2o. With thumb over the hole, shake up and filter out the red (its good to have a few test tubes clean and handy) by pouring liquid into another test tube using small funnel and 1 coffee filter (saturate filter with dh2o prior to using.) Now your left with a clear, yellowish liquid. CrystallizationMaterials
Add 8gm of lye to a clean test tube. Now add 20mL of dh2o and mix well (use gloves if you shake tube using your finger as a stopper!) then place in sand to cool. Add 50mL lighter fluid to the tube with your yellow liquid. When cool add the lye solution SLOWLY to the tube with the yellow liquid and lighter fluid. Don't pour it in all at once, add splashes until gone. Cover the hole and give it one good shake, release the pressure and place in sand for approx. 15 minutes. Your lye will be locked on the bottom which is fine. Pour off lighter fluid into a clean test tube. Add 20mL dh2o, 4 drops of acid and shake hard. Use an eye dropper to get the bottom layer, attaching aquarium vacuum tubing to extend the length if needed. Pour this onto your glass dish and evaporate. What remains after dh2o evaporates is pure meth. Scrape crystals with razor and enjoy! That's all folks! |