MDP2P from isosafrole via the dibromide, bromohydrin and epoxideby Uemura[ Back to the Chemistry Archive ] The following experimental procedures disclose an old, but in the Hive not much -if any- discussed or known approach from the propenylbenzenes to the 2-propanones. The methods to be shown are easy, do not require any special chemicals and give all high yields in each of the steps from the propenylbenzen to the ketone. Likely not state of the art -the procedures are almost 100 years old-, this write-up gives nevertheless one so-far UNKNOWN clue on the epoxide-ketone re-arrangement mechanism. The write-up is mainly based on the article of (1) Höring, 'Über die Dibromide aromatischer Propenylverbindungen', Ber 38, 1905, pg. 3464 and the article of (2) Mannich, 'Studien in der Reihe des Adrenalins', Arch. Phar. Bd 248, 1910, pg. 127. Uemura picked up the essential details from these two papers, some notes are added the end. It should be noted that the authors have performed the ketone preparation on the anethole and isosafole, but, and this is where it may becomes interesting, it could work for the acid sensitive asarone as well. Isosafroledibromine (CH2O2:)C6H3.CHBr.CHBr.CH3 100g Isosafrole is diluted with 100ml petrol ether. Under cooling with ice a solution of 100g bromine in 100ml petrol is added drop wise. If cristals of the Isosafrolebromide are around, some cristals are added to initiate cristallisation when the addition of bromine has finished. The flask is put on ice and the lower part consisting of the dibromide gets solid after some hours. Yield 203g. The dibromide does not easily cristallize. mp is 52-53°C. [N1] Isosafrolebromhydrine (CH2O2:)C6H3.CHOH.CHBr.CH3 100g Isosafroledibromine are dissolved in 300ml acetone, water is added as long as the solution stays clear (appr. 50ml). In addition, 16g of marble pieces (CaCO3) are added to catch up the HBr which is produced by the hydrolyse of the dibromide. Carbon dioxide develops already in the cold. The mixture is heated then 2 hours on a hot waterbath. After 2 hours the aqueous CaBr2 solution is removed and another 40ml water is added. 2 more hours the rxn is heated on a water bath. Then the acetone is removed by destillation. The oily Isosafrolebromhydrine is extracted with ether [N3], the ether solution is washed with water and dried in vacuum. Evap the ether. Yield 98%. The Isosafrolbromhydrine cannot be destilled in vacuum but will be used as it is for the next step. [N2] Isosafroleepoxide (CH2O2:)C6H3.CHOCH.CH3 100g Isosafrolbromhydrine are disolved in 100ml alcohol. A solution of 25g KOH in 200ml alcohol is added. Immediately KBr seperates. The alcoholic solution is refluxed on a waterbath to complete the reaction. [N4] Most of the alcohol is then removed by destillion. The solution is poured into water and the Isosafroleepoxide extracted with ether [N3]. Ether solution is dried and evaporated. Yield with respect to the dibromide is 88%. The Isosafroleepoxide is a colorless, good smelling oil which boils between 143-147°C under 12mm pressure. [N5] 3,4-Methylenedioxyphenyl-2-propanone, (CH2O2:)C6H3.CHOCH.CH3 i.e. Isosafrole-2-propanone, MDP2P The conversion of the Isosafroleepoxide into the ketone starts when the epoxide is heated to 220°C in a flask equipped with a air-cooled condenser. The temperature jumps up quickly to 280°C. When the exothermic rxn has finished, the mix is refluxed for a short period of time. The first destillation under normal pressure yields a colorless, almost non-smelling oil, which comes over between 280-290°C. Under 10mm pressure it boils between 149-151°C. Yield 80% [N6] Isosafrole-2-propanone-oxime (CH2O2:)C6H3.CHNOHCH.CH3 [N7] 3g ketone are solved in ethanol, 3g Hydroxylammonumchlorid, solved in a minimum amount of water, are added and the combined solution is make alkaline with concentrated Na2CO3 solution. After standing (hours..) and dilution with water, needles of the oxime seperate. They melt at 87°C. Recrist. from ethanol or et ether. Notes:
|